Backing Pads
Brand: TORK CRAFT
MPN: SPC00053
Adaptor for a polisher
Thread: 5/8' BSP Male - M14 Female
Application:
The adaptor is used to extend the spindle shaft on a polisher. Some adaptors
have different threads on either end. These adaptors are mostly used to change
an imperial thread to a metric thread.
DEFINITION:
BSP - British Standard Pipe thread.
M - ISO metric screw thread.
....
N$ 81.65
Ex VAT:N$ 71.00
Brand: TORK CRAFT
MPN: SPC00055
Adaptor for a polisher
Thread: 5/8' BSP Male - 5/8' BSP Female
Application:
The adaptor is used to extend the spindle shaft on a polisher. Some adaptors
have different threads on either end. These adaptors are mostly used to change
an imperial thread to a metric thread.
DEFINITION:
BSP - British Standard Pipe thread.
....
N$ 81.65
Ex VAT:N$ 71.00
Brand: TORK CRAFT
MPN: SPC00054
Adaptor for a polisher
Thread: 5/8' UNC Female - M14 Male
Application:
The adaptor is used to extend the spindle shaft on a polisher. Some adaptors
have different threads on either end. These adaptors are mostly used to change an
imperial thread to a metric thread.
DEFINITION:
M - ISO metric screw thread.
....
N$ 81.65
Ex VAT:N$ 71.00
Brand: TORK CRAFT
MPN: SPC00051
Adaptor for a polisher
Thread: M14 Male - Ø8mm
spindle
Application:
The adaptor is used to connect a drill with a 3 jaw chuck to a M14 polishing
backing pad. Eg.
SPC00106.
DEFINITION:
M - ISO metric screw thread.
....
N$ 67.85
Ex VAT:N$ 59.00
Brand: TORK CRAFT
MPN: SPC00052
Adaptor for a polisher
Thread:
M14 Male - M14 Female
Application:
The adaptor is used to extend the spindle shaft on a polisher. Some adaptors
have different threads on either end. These adaptors are mostly used to change
an imperial thread to a metric thread.
DEFINITION:
M - ISO metric screw thread.
....
N$ 81.65
Ex VAT:N$ 71.00
Brand: TORK CRAFT
MPN: TCPS3506
Adjustable Pin Spanner for Angle Grinder - 15-52 x 4mm
Pin Centers: 15 - 52mm
Too big - too small, adjust the fit. Tork Craft's adjustable pin spanner is designed to fit most Angle grinder
flange nuts and more with pin hole diameters of 4mm, ranging from 15mm-52mm centre to centre pin spacing.
At the bottom end of the spanner is a flat tip allowing for easy paint can opening as well as built into the handle is a
basic wrench with sizes 10,12,13,14,15,17,19mm. This 3-in-1 t..
N$ 140.30
Ex VAT:N$ 122.00
Brand: TORK CRAFT
MPN: TCBP178-1
Backing pad for angle grinder
Backing pad to be used with an angle grinder to polish stone.
DIA: 100mm
THREAD: M14
Hook & Loop: No
MAX RPM: 8,600
Application:
This is a backing pad for an angle grinder to use fibre discs.
The range of fibre discs can be viewed
here.
CAUTION:
Due to the high rotation speed of angle grinders, it is not recommended to use
polishing bonnets with this backing pad.
ATTENTION:
Wear eye, face and body protection....
N$ 135.13
Ex VAT:N$ 117.50
Brand: TORK CRAFT
MPN: TCBP115-3
Backing pad for angle grinder
Backing pad to be used with an angle grinder with M14 thread.
DIA: 115mm
THREAD: M14
Hook & Loop: No
DENSITY: Hard
MAX RPM: 11,500
Application:
This is a backing pad for an angle grinder to use fibre discs.
The range of fibre discs can be viewed
here.
CAUTION:
Due to the high rotation speed of angle grinders, it is not recommended to use
polishing bonnets with this backing pad.
ATTENTION:
Wear eye, face and body protection....
N$ 111.78
Ex VAT:N$ 97.20